Powder coat look. No teardown.
Colour-shift vinyl wraps for e-motos. Sur-Ron, Talaria, E Ride Pro and more.
Powder coat vs EWA wrap
| Powder coat | EWA wrap | |
|---|---|---|
| Strip and rebuild the bike | Hours pulling the frame apart and putting it back together | Not needed, it goes straight on the frame |
| Time off the road | Days to weeks waiting on the shop | Ride again the same weekend |
| Do it yourself | No, it needs a shop and an oven | Yes, at home with our tool kit |
| Sparkle and colour-shift finishes | Limited and pricey | Built in |
| Change your mind | Sandblast it off and start again | Peel it off and swap colours |
| Protects the original paint | No, the frame gets stripped | Yes, the wrap sits over it |
| Cost | Shop quote plus labour | From $130 |
Featured product
Midnight Blue Colour-Shift E-Moto Wrap
Pickup currently not available
Tracked shipping
Australia-wide and worldwide, tracking emailed with every order.
Secure checkout
Pay safely with card, Apple Pay, Google Pay or Shop Pay.
Easy DIY install
Step-by-step guide included. Fit it in a weekend.
Real support
Questions about fitment? Email us and we will help.
Skip the 40-hour strip down and rebuild
Powder coating means pulling every bolt, wire, wheel and battery off your bike, then waiting on the shop and paying $800+. Our wraps go straight onto the frame in a weekend.
Weekend install
No teardown, no shop wait.
Fraction of the price
From $130 vs $800+ powder coat.
Fits most e-motos
Sur-Ron, Talaria, E Ride Pro, Stark and more.
How to get a perfect wrap
1. Prep your space
Work somewhere shaded and not too cold, and take the battery lid off before using heat.
2. Clean it
Wash the bike, then wipe everything with rubbing alcohol so the wrap sticks properly.
3. Cut your pieces
Cut a piece for each part with a bit of extra around the edges.
4. Lay it on
Peel the backing, lay the wrap down lightly and adjust it until it sits right. It lifts off easily if you need another go.
5. Smooth it out
Push the air out from the middle to the edges with the squeegee.
6. Use a little heat on curves
Warm the wrap with a heat gun so it bends around tubes and corners easily.
7. Trim the edges
Cut off the extra and press every edge down firmly.
8. Heat it to lock it in
Go over the whole wrap with the heat gun so it stays put, then wait a week before washing.
FAQ
Will it fit my bike?
One 50 x 300 cm roll covers the frame of most e-motos, including Sur-Ron, Talaria, E Ride Pro and Stark, with spare left over.
How long does shipping take?
Australia: Standard 7-15 business days ($10) or Express 4-8 business days ($15). International: usually 10-25 business days.
Is it hard to install?
Not at all. Clean the frame, lay each piece on, smooth it out and use a heat gun on curves and to lock it in. Most people finish over a weekend, and our tool kit add-on has everything you need.
Can I remove it later?
Yes. The vinyl peels off cleanly, so you can change colour any time.
What if there is a problem with my order?
Email emotowrapsau@gmail.com and we will sort it out. See our Refund Policy for details.
How long does it take?
Most people do it over a weekend. Take your time on your first one, it gets much quicker with practice.
Do I need a heat gun?
Yes. A hair dryer helps on curves, but a heat gun is what locks the wrap in place so edges don't lift later. A basic one is fine.
Can I wash my bike?
Yes, after the first week. Hand wash with mild soap and a soft cloth. If you use a pressure washer, keep it on a wide spray, stay back, and don't aim at the edges.
How long will it last?
With good care and the bike stored out of the sun, it typically lasts a few years. Strong sun, crashes and pressure washing will shorten that.
Will it damage my frame?
No. Over factory paint or powder coat it actually protects the finish, and it peels off cleanly when warmed with a heat gun. Avoid wrapping over chipped or freshly painted spots.